Western Builder

Dedicated to the people who make our built environment better and safer. We tell your stories and celebrate your successes.

Register with us and receive industry news and content only available to subscribers.

Subscribe
Contacts

Indianapolis, IN, USA (HQ)

903 E. Ohio St., Indianapolis, IN 46202

Call: (317) 423-2325

info@acppubs.com

Solving the Suspension Scaffold Rescue Challenge

It’s been on the news time and time again — a window washer crew or a crew utilizing some form of suspension scaffold is trapped in mid-air stories above the ground. Their work platform has failed in some way, and the workers are dangling from their safety lifeline. With no rescue plan in place, rescue could take hours, putting the workers’ safety and health at risk.

“According to OSHA 1910.27(b)(2)(viii) standards, employers must provide prompt rescue of each worker in the event of a fall,” said SMG Director of Construction and Manufacturing Craig Clark, CHST. “That means employers need to develop and implement a plan for effective rescue. It also requires employers to provide the resources like equipment and rescue personnel and ensure employees understand the rescue plan.”

Understanding the Standards
Before getting into a discussion of rescue for this type of work, it makes sense to start with the definition of a rope descent system, which OSHA 1910.27(b) defines as follows:

“A suspension system that allows a worker to descend in a controlled manner, and, as needed, to stop at any time during the descent. A rope descent system usually consists of a roof anchor, support rope, a descent device, carabiner(s) or shackle(s), and a chair (seatboard).”

The standard also requires that the employee have a “backup safety system” should the main suspension system fail. Standard 1910.27(b)(2)(vi) requires that each worker uses a separate, independent personal fall arrest system when using a rope descent system.

Another often overlooked piece to the standard is 1910.27(b)(2)(i), requiring employers ensure no rope descent system is used at heights above 300 feet above grade. Exceptions to the 300-foot limit are granted when it can be demonstrated that it is not feasible to access heights above 300 feet by other means or in cases where alternative means of access pose a greater hazard than using a rope descent system.

What’s the Plan?
“Unfortunately, many companies often fail to implement a plan of rescue to get workers down who are doing at height work using suspension scaffolds,” Clark said. “They do, however, follow the part of the standard that provides the worker with a safety backup lifeline. If these companies would make it part of their plan to invest in a few pieces of additional equipment and employee training, they would never have to rely on fire and rescue as the alternative plan.”
LBX Link Belt Excavators
Your local Link Belt dealer
Hayden-Murphy Equipment Co

In addition, some fire departments aren’t always trained or equipped to respond to these types of rescue situations with suspension scaffolds – often taking place at heights of more than 200 feet. For employers who have workers using suspension scaffolds and rope descent systems, a representative of the company should contact your local fire department and ask a few questions, such as:

  • Do you have a ladder truck? If so, how tall will it reach?
  • Are your responders trained in height or high-angle rescue?
  • Is your department volunteer?
  • What is your average response time?

A simple solution to the suspension scaffold rescue challenge lies in the safety backup line.

Pre-Rig to Lower Systems
“The safety backup line is a pre-rigged to lower system,” Clark said. “It’s a system rope access technicians have been using for years. Your backup safety system or lifeline must be anchored to an anchor point that is separate from the anchorage supporting the suspension scaffold system.”

A pre-rigged to lower system utilizes an additional rope descent system – Petzl ID – that anchors to the lifeline anchor instead of your lifeline attaching to it. The lifeline is then run through the Petzl ID, and the ID is locked in the stowed position.

The pre-rig to lower system also requires more lifeline rope than is normally used – the rule of thumb is two and a half times the distance of the structure being climbed. For example, if a building was 100 feet tall, you would use 250 feet of rope. A pully can also be connected at the anchor rather than the Petzl ID. The Petzl ID can then be rigged at the ground level so there is no need for the rescuer to go to the top of the structure to perform the rescue.

It’s Rescue Time
Here’s the scenario: You are the “ground person” who assists an individual working at height on some type of suspension scaffold. You’re stationed on the roof to lower materials to the worker as needed and to monitor the worker’s equipment and anchors. (This is not a requirement mandated by any federal organization.). You hear a noise close by and notice one of the anchor lines for the suspension scaffold has failed. You also notice the lifeline rope now has a great deal of tension on it. You look over the edge, and you see your coworker dangling on their lifeline!

In most situations, the ground person would call 911 and request assistance. Suspension trauma – or orthostatic shock – happens when a fallen worker is suspended in a harness with legs hanging. And it can occur in a worker in 15 to 40 minutes, so it must be treated as an emergency. How long will it take for responders to arrive and rescue your coworker?

With a pre-rigged to lower device in place and with the proper training, the ground person would simply unlock their rope descent system and use the device to lower the suspended worker to ground. And that’s at a rate of 3 feet a second.

“Employers need to make sure all employees who work at heights are fully trained in fall protection as well as how on-site equipment should be used and what steps to take in an emergency situation,” Clark said.

If you are a business that performs work in this sector, it’s important to learn more about the pre-rigged to lower systems available and how this cost-effective equipment could be implemented in your work environment. This method of rescue is a part of SMG’s At-Height Rescue training course. Go to safetymanagementgroup.com/contact/ to learn more.

Komatsu Dealer Program
Your local Komatsu America Corp dealer
Road Machinery and Supplies Company
Komatsu Dealer Program
Your local Komatsu America Corp dealer
Road Machinery and Supplies Company